Part Number Hot Search : 
68FAUE 14600 HM6147H MAX700 RW48B AT2564 TA123 BFC2808
Product Description
Full Text Search
 

To Download AOZ2253EQI-30 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  rev 1.1 march 2018 www.aosmd.com page 1 of 15 AOZ2253EQI-30 28v/8a synchronous ezbuck tm regulator general description the AOZ2253EQI-30 is a high-efficiency, easy-to-use dc/dc synchronous buck regulator that operates up to 28v. the device is capable of supplying 8a of continuous output current with an output voltage adjustable down to 0.8v 1%. the AOZ2253EQI-30 integrates an internal linear regulator to generate 5.3v v cc from input. if input voltage is lower than 5.3v, the linear regulator operates at low drop output mode, which allows the v cc voltage is equal to input voltage minus the drop-output voltage of the internal linear regulator. a proprietary constant on-time pwm control with input feed-forward results in ultra-fast transient response while maintaining relatively constant switching frequency over the entire input voltage range. the device features multiple protection functions such as v cc under-voltage lockout, c ycle-by-cycle current limit, output over-voltage protection, short-circuit protection, and thermal shutdown. the AOZ2253EQI-30 is available in a 4mm4mm qfn- 22l package and is rated over a -40c to +85c ambient temperature range. features ? wide input voltage range C 6.5v to 28v ? 8a continuous output current ? output voltage adjustable down to 0.8v (1.0%) ? low r ds(on) internal nfets C 28m ? high-side C 11m ? low-side ? constant on-time with input feed-forward ? ceramic capacitor stable ? adjustable soft start ? integrated bootstrap diode ? cycle-by-cycle current limit ? short-circuit protection ? thermal shutdown ? thermally enhanced 4mm x 4mm qfn-22l package applications ? compact desktop pcs ? graphics cards ? set-top boxes ? lcd tvs ? cable modems ? point-of-load dc/dc converters ? telecom/networking/datacom equipment typical application AOZ2253EQI-30 input 6.5v to 28v output 1v, 8a c3 88f r1 r2 c2 22f c5 0.1f analog ground power ground off on vccen ss c ss c4 4.7f bst lx fb agnd pgnd l1 1h in 5.3v c ton 100pf ton r ton downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 2 of 15 option table recommended start-up sequence part number pfm / force pwm for light load operation pfm force pwm AOZ2253EQI-30 v aoz2253eqi-31 v vin en 50s downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 3 of 15 ordering information aos green products use reduced levels of halogens, and are also rohs compliant. please visit www.aosmd.com/media/aosgreenpolicy.pdf for additional information. pin configurationpin description part number ambient temperature range package environmental AOZ2253EQI-30 -40c to +85c 22-pin 4mm x 4mm qfn green product pin number pin name pin function 1e n enable input. the AOZ2253EQI-30 is enabled wh en en is pulled high. the device shuts down when en is pulled low. 2f b feedback input. adjust the output voltage with a resistive voltage-divider between the regulators output and agnd. 3 agnd analog ground. 6a i n supply to internal analog function. ain pin must be connected to in pins. for noisy operation, its better to have a rc filter from in to ain for better noise immunity. 7, 8, 9 in supply input. in is the regulator in put. all in pins must be connected together. 10, 11, 16, 17, 18 lx switching node. 12, 13, 14, 15 pgnd power ground. 19 ton on-time setting input. connect a resist or between vin and ton to set the on time 20 bst bootstrap capacitor connection. the AOZ2253EQI-30 includes an internal bootstrap diode. connect an external capacitor between bst and lx as shown in typical application diagram. 21 vcc supply input for analog functions. bypass vcc to agnd with a 4.7f~10f cerami c capacitor. place the capacitor close to vcc pin. 22 ss soft-start time setting pin. connect a capacitor between ss and agnd to set the soft- start time. 1 22 21 20 19 18 789 11 10 23 4 5 en inin in lxlx ssvcc bst ton lx fb agnd nc nc 22-pin 4mm x 4mm qfn (top view) 1716 15 13 12 lxlx pgnd pgnd pgnd pgnd lx in 14 6 ain downloaded from: http:///
rev 1.1 march 2018 www.aosmd.com page 4 of 15 AOZ2253EQI-30 absolute maximum ratings exceeding the absolute maximum ratings may damage the device. notes: 1. lx to pgnd transient (t<20ns) ------- -7v to v in +7v. 2. devices are inherently esd s ensitive, handling precautions are required. human body model rating: 1.5k ? in series with 100pf. maximum operating ratings the device is not guaranteed to operate beyond the maximum operating ratings. parameter rating in, ton to agnd -0.3v to 30v lx to agnd (1) -0.3v to 30v bst to agnd -0.3v to 36v ss, fb, en, vcc to agnd -0.3v to 6v pgnd to agnd -0.3v to +0.3v junction temperature (t j ) +150c storage temperature (t s ) -65c to +150c esd rating (2) 2kv parameter rating supply voltage (v in ) 6.5v to 28v output voltage range 0.8v to 0.85*v in ambient temperature (t a ) -40c to +85c package thermal resistance ( ? ja ) ( ? jc ) 32c/w 4c/w electrical characteristicst a = 25c, v in =12v, en = 5v, unless otherwise specified. specifications in bold indicate a temperature range of -40c to +85c. symbol parameter conditions min. typ. max units v in in supply voltage 6.5 28 v v uvlo under-voltage lockout threshold v cc rising v cc falling 3.2 4.03.7 4.4 v i q quiescent supply current of v cc i out = 0, v en > 2v, pfm 0.16 ma i off shutdown supply current v en = 0v 15 ? a v fb feedback voltage t a = 25c t a = 0c to 85c 0.7920.788 0.800 0.800 0.808 0.812 v load regulation 0.5 % line regulation 1% i fb fb input bias current 200 na enable v en en input threshold off threshold on threshold 1.6 0.5 v v en_hys en input hysteresis 100 mv modulator t on _ min minimum on time 60 ns t on _ max maximum on time 2.6 ? s t off _ min minimum off time 300 ns soft-start i ss _ out ss source current v ss = 0 c ss = 0.001 ? f to 0.1 ? f 71 11 5 ? a under voltage and over voltage protection v pl under voltage threshold fb falling 70 % t pl under voltage delay time 32 ? s v ph over voltage threshold fb rising 120 % power stage output downloaded from: http:///
rev 1.1 march 2018 www.aosmd.com page 5 of 15 AOZ2253EQI-30 r ds(on) high-side nfet on-resistance v in = 12v 28 m ? high-side nfet leakage v en = 0v, v lx = 0v 10 ? a r ds(on) low-side nfet on-resistance v lx = 12v 11 m ? low-side nfet leakage v en = 0v 10 ? a over-current and thermal protection i lim current limit 12 a thermal shutdo wn threshold t j rising t j falling 150 100 c electrical characteristicst a = 25c, v in =12v, en = 5v, unless otherwise specified. specifications in bold indicate a temperature range of -40c to +85c. symbol parameter conditions min. typ. max units downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 6 of 15 functional block diagram isense ilim error comp ilim comp 0.8v isense (ac) fb decode otp bst agnd pgnd isenseisense (ac) current information processing vcc in uvlo ldo toff_min s r q timer q fb ss light load threshold isense light loadcomp vcc en reference & bias lx ton timer q en ton ton generator downloaded from: http:///
rev 1.1 march 2018 www.aosmd.com page 7 of 15 AOZ2253EQI-30 typical performance characteristics circuit of typical application. t a = 25c, v in = 12v, v out = 1v, unless otherwise specified. normal operation vlx(20v/div) ilx (5a/div) v o ripple (20mv/div) 10s/div load transient 0a to 8a ilx (10a/div) v o ripple (100mv/div) 1ms/div full load start-up ilx(10a/div) (500mv/div) en (5v/div) vlx(20v/div) 1ms/div v o short circuit protection vlx (20v/div) ilx(20a/div) v o (1v/div) 20s/div efficiency (%) output current (a) 0 2.0 4.0 8.0 6.0 efficiency vs. load current vin = 6.5v vin = 12v vin = 19v vin = 24v 100 9080 70 60 50 40 30 20 10 0 v out = 1v downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 8 of 15 detailed description the AOZ2253EQI-30 is a high-efficiency, easy-to-use, synchronous buck regulator optimized for notebook computers. the regulator is capable of supplying 8a of continuous output current with an output voltage adjustable down to 0.8v. the input voltage of AOZ2253EQI-30 can be as low as 6.5v. the highest input voltage of AOZ2253EQI-30 can be 28v. constant on-time pwm with input feed-forward control scheme results in ul tra-fast transient response while maintaining relatively constant switching frequency over the entire input range. true ac current mode control scheme guarantees the regul ator can be stable with ceramics output capacitor. protection features include v cc under-voltage lockout, current limit, output over voltage and under voltage protection, short-circuit protection, and thermal shutdown. the AOZ2253EQI-30 is available in 22-pin 4mm4mm qfn package. input power architecture the AOZ2253EQI-30 integrates an internal linear regulator to generate 5.3v (5%) v cc from input. if input voltage is lower than 5.3v, the linear regulator operates at low drop-output mode; the v cc voltage is equal to input voltage minus the drop-output voltage of internal linear regulator. enable and soft start the AOZ2253EQI-30 has external soft start feature to limit in-rush current and ensure the output voltage ramps up smoothly to regulate voltage. a soft start process begins when v cc rises to 4.5v and voltage on en pin is high. an internal current source charges the external soft-start capacitor; the fb voltage follows the voltage of soft-start pin (v ss ) when it is lower than 0.8v. when v ss is higher than 0.8v, the fb voltage is regulated by internal precise band-gap voltage (0.8v). the soft-start time for fb voltage can be calculated by the following formula: t ss ( ? s) = 80 x c ss (nf) if c ss is 1nf, the soft-start time will be 80 seconds; if c ss is 10nf, the soft-start time will be 800 seconds. figure 1. soft start sequence of AOZ2253EQI-30 constant-on-time pwm control with input feed-forward the control algorithm of AOZ2253EQI-30 is constant-on- time pwm control with input feed-forward. the simplified control schematic is shown in figure 2 . the high-side switch on-time is determined solely by a one-shot whose pulse width is inversely propor tional to input voltage (in). the one-shot is triggered when the internal 0.8v is higher than the combined information of fb voltage and the ac current information of inductor, which is processed and obtained through the sensed low-side mosfet current once it turns-on. the added ac current information can help the stability of constant -on time control even with pure ceramic output capacitors, which have very low esr. the ac current informatio n has no dc offset, which does not cause offset with output load change, which is fundamentally different from other v 2 constant-on time control schemes. figure 2. simplified control schematic of AOZ2253EQI-30 the constant-on-time pwm co ntrol architecture is a pseudo-fixed frequency with input voltage feed-forward. the internal circuit of AOZ2253EQI-30 sets the on-time of high-side switch inversely proportional to the in. to achieve the flux balance of inductor, the buck converter has the equation: (1)(2) v out v ss v ss = 3.3v v ss = 0.8v + C programmable one-shot in comp fb voltage/ac current information 0.8v pwm ) ( ) ( v v r t in ton on ? ? on in out sw t v v f * ? downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 9 of 15 once the product of v in *t on is constant, the switching frequency keeps constant and is independent of input voltage. an external resistor between the in and ton pins sets the switching on-time accord ing to the following curves: figure 3 . ton vs. rton curves for AOZ2253EQI-30 a further simplified equation will be : if v o is 1v, v in is 19v, and set fs=400khz. according to eq.(3), t on =131.6ns is needed. finally, use the t on to r ton curve, we can find out r ton is 300k ? . this algorithm results in a nearly constant switching frequency despite the lack of a fixed-frequency clock generator. true current mode control the constant-on-time contro l scheme is intrinsically unstable if output capacitors esr is not large enough as an effective current-sense resistor. ceramic capacitors usually can not be used as output capacitor. the AOZ2253EQI-30 senses the low-side mosfet current and processes it into dc current and ac current information using aos proprietary technique. the ac current information is decoded and added on the fb pin on phase. with ac current information, the stability of constant-on-time control is significantly improved even without the help of output capacitors esr; and thus the pure ceramic capacitor solution can be applicant. the pure ceramic capacitor soluti on can significantly reduce the output ripple (no esr caused overshoot and undershoot) and less board area design. current-limit protection the AOZ2253EQI-30 has the current-limit protection by using r dson of the low-side mosfet to be as current sensing. to detect real cu rrent information, a minimum constant off-time (300ns typical) is implemented after a constant-on time. if the current exceeds the current-limit threshold, the pwm controller is not allowed to initiate a new cycle. the actual peak current is greater than the current-limit threshold by an amount equal to the inductor ripple current. therefore, the exact current-limit characteristic and maximum load capability are a function of the inductor value and input and output voltages. the current limit will keep the lo w-side mosfet on and will not allow another high-side on-time, until the current in the low-side mosfet reduces below the current limit. after 8 switching cycles, th e AOZ2253EQI-30 considers this is a true failed condition and thus turns-off both high- side and low-side mosfet and shuts down . the AOZ2253EQI-30 enters hiccup mode to periodically restart the part. when the current limit protection is removed, the AOZ2253EQI-30 exits hiccup mode. output voltage under-voltage protection if the output voltage is lower than 70% by over-current or short circuit, aoz2 253eqi-30 will wait for 32s (typical) and turns-off both high-side and low-side mosfet and shuts down. when the output voltage under-voltage protection is removed, the AOZ2253EQI-30 restarts again. output voltage over-voltage protection the threshold of ovp is set 20% higher than 0.8v. when the v fb voltage exceeds the ovp threshold, high-side mosfet is turn-off and lo w-side mosfet is turn-on 1s, then shuts down. when the output voltage over- voltage protection is removed, the AOZ2253EQI-30 restarts again. (3) ton vs. rton @ vin = 6.5v~16v 0.00 100.00 200.00 300.00 400.00 500.00 600.00 700.00 800.00 900.00 1000.00 1100.00 200 250 300 350 400 450 500 550 600 650 700 750 800 ton (ns) rton (k) vin=6.5 vin=8 vin=10 vin=12 vin=14 vin=16 ton vs. rton @ vin = 18v~28v 0.00 50.00 100.00 150.00 200.00 250.00 300.00 350.00 400.00 450.00 500.00 200 250 300 350 400 450 500 550 600 650 700 750 800 ton (ns) rton (k) vin=18 vin=19 vin=21 vin=24 vin=26 vin=28 6 10 ) ( )( )( ) ( ? ? ? ns t v v v v khz f on in out sw downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 10 of 15 application information the basic AOZ2253EQI-30 app lication circuit is shown in the typical application secti on. the component selection is explained below. input capacitor the input capacitor must be connected to the in pins and pgnd pin of the AOZ2253EQI-30 to maintain steady input voltage and filter out the pulsing input current. a small decoupling capacitor, usually 4.7f, should be connected to the v cc pin and agnd pin for stable operation of the AOZ2253EQI-30. the voltage rating of input capacitor must be greater than maximum input voltage plus ripple voltage. the input ripple voltage can be approximated by equation below: since the input current is discontinuous in a buck converter, the current stress on the input capacitor is another concern when selecting the capacitor. for a buck circuit, the rms value of input capacitor current can be calculated by: if let m equal the conversion ratio: the relation between the input capacitor rms current and voltage conversion rati o is calculated and shown in figure 4. it can be seen that when v o is half of v in , c in it is under the worst current stress. the worst current stress on c in is 0.5 x i o . figure 4. i cin vs. voltage conversion ratio for reliable operation and best performance, the input capacitors must have current rating higher than i cin-rms at worst operating conditions. ceramic capacitors are preferred for input capacito rs because of their low esr and high ripple current rating. depending on the application circuits, other low esr tantalum capacitor or aluminum electrolytic capacitor may also be used. when selecting ceramic capacitors, x5r or x7r type dielectric ceramic capacitors are preferred for their better temperature and voltage charac teristics. note that the ripple current rating from capacitor manufactures is based on certain amount of life time. further de-rating may be necessary for practical design requirement. inductor the inductor is used to supply constant current to output when it is driven by a swit ching voltage. for given input and output voltage, inductance and switching frequency together decide the inductor ripple current, which is: the peak inductor current is: high inductance gives low inductor ripple current but requires larger size inductor to avoid saturation. low ripple current reduces inductor core losses. it also reduces rms current through inductor and switches, which results in less cond uction loss. usually, peak to peak ripple current on inductor is designed to be 30% to 50% of output current. when selecting the inductor, make sure it is able to handle the peak current without saturation even at the highest operating temperature. the inductor takes the highest current in a buck circuit. the conduction loss on inductor needs to be checked for thermal and efficiency requirements. surface mount inductors in different shape and styles are available from coilcraft, elytone and murata. shielded inductors are small and radiate less emi noise. but they cost more than unshield ed inductors. the choice depends on emi requirement, price and size. output capacitor the output capacitor is selected based on the dc output voltage rating, output ripple voltage specification and ripple current rating. (4) (5) (6) ? v in i o fc in ? ----------------- 1 v o v in -------- - C ?? ?? ?? v o v in -------- - ? ? = i cin_rms i o v o v in -------- - 1 v o v in -------- - C ?? ?? ?? ? = v o v in -------- - m = 0 0.1 0.2 0.3 0.4 0.5 0 0.5 1 m i cin_rms (m) i o (7) (8) ? i l v o fl ? ---------- - 1 v o v in -------- - C ?? ?? ?? ? = i lpeak i o ? i l 2 -------- + = downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 11 of 15 the selected output capacitor must have a higher rated voltage specification than the maximum desired output voltage including ripple. de-rating needs to be considered for long term reliability. output ripple voltage specif ication is another important factor for selecting the output capacitor. in a buck converter circuit, output ripple voltage is determined by inductor value, switching frequency, output capacitor value and esr. it can be calculated by the equation below: where , c o is output capacitor value and esr co is the equivalent series resistor of output capacitor. when low esr ceramic capacitor is used as output capacitor, the impedance of the capacitor at the switching frequency dominates. output ripple is mainly caused by capacitor value and inductor ripple current. the output ripple voltage calculation can be simplified to: if the impedance of esr at switching frequency dominates, the output ripple voltage is mainly decided by capacitor esr and inductor ripple current. the output ripple voltage calculation can be further simplified to: for lower output ripple voltage across the entire operating temperature range, x5r or x7r dielectric type of ceramic, or other low esr tantalum are recommended to be used as output capacitors. in a buck converter, output capacitor current is continuous. the rms current of output capacitor is decided by the peak to peak inductor ripple current. it can be calculated by: usually, the ripple current rating of the output capacitor is a smaller issue because of the low current stress. when the buck inductor is select ed to be very small and inductor ripple current is high, output capacitor could be overstressed. thermal management and layout consideration in the AOZ2253EQI-30 buck regulator circuit, high pulsing current flows through two circuit loops. the first loop starts from the input capac itors, to the in pin, to the lx pins, to the filter inductor, to the output capacitor and load, and then return to the input capacitor through ground. current flows in the first loop when the high side switch is on. the second loop starts from inductor, to the output capacitors and load , to the low side switch. current flows in the second loop when the low side low side switch is on. in pcb layout, minimizing th e two loops area reduces the noise of this circuit and improves efficiency. a ground plane is strongly recommended to connect input capacitor, output capacitor, and pgnd pin of the AOZ2253EQI-30. in the AOZ2253EQI-30 buck regulator circuit, the major power dissipating components are the AOZ2253EQI-30 and the output inductor. the total power dissipation of converter circuit can be measured by input power minus output power. the power dissipation of inductor can be approximately calculated by output current and dcr of inductor and output current. the actual junction temper ature can be calculated with power dissipation in the AOZ2253EQI-30 and thermal impedance from junction to ambient. the maximum junction temperature of AOZ2253EQI-30 is 150oc, which limits the maximum load current capability. the thermal performance of the AOZ2253EQI-30 is strongly affected by the pcb layout. extra care should be taken by users during design process to ensure that the ic will operate under the recommended environmental conditions. (9) (10) (11) (12) ? v o ? i l esr co 1 8 fc o ? ? ------------------------- + ?? ?? ? = ? v o ? i l 1 8 fc o ? ? ------------------------- ? = ? v o ? i l esr co ? = i co_rms ? i l 12 ---------- = (13) (14) (15) p total_loss v in i in v o i o ? C ? = p inductor_loss i o 2 r inductor 1.1 ? ? = a ja loss inductor loss total junction t p p t ? ?? ? ? ) ( _ _ downloaded from: http:///
rev 1.1 march 2018 www.aosmd.com page 12 of 15 AOZ2253EQI-30 layout considerations several layout tips are listed below for the best electric and thermal performance. 1. the lx pins and pad are connected to internal low side switch drain. they are low resistance thermal conduction path and most noisy switching node. connected a large copper plane to lx pin to help thermal dissipation. 2. the in pins and pad are connected to internal high side switch drain. they are also low resistance thermal conduction path. connected a large copper plane to in pins to help thermal dissipation. 3. input capacitors should be connected to the in pin and the pgnd pin as close as possible to reduce the switching spikes. 4. decoupling capacitor c vcc should be connected to v cc and agnd as close as possible. 5. voltage divider r1 and r2 should be placed as close as possible to fb and agnd. 6. keep sensitive signal traces such as feedback trace far away from the lx pins. 7. pour copper plane on all unused board area and connect it to stable dc nodes, like vin, gnd or vout. 1 2 3 4 5 6 e n f b a g n d n c n c a i n 7 9 1 0 i n i n 1 8 1 9 2 0 2 1 1 6 1 5 1 3 1 2 l x l x l x p g n d p g n d i n 2 2 1 4 p g n d 8 i n l x 1 1 l x 1 7 p g n d l x t o n b s t v c c s s v out c out l c vcc c b v out r1 r2 c in v in pgnd downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 13 of 15 package dimensions, qf n 4x4, 22 lead ep2_s top view side view bottom view notes:1. controlling dimensions are in millimeters. converted inch dimensions are not necessarily exact. 2. tolerance: 0.05 unless otherwise specified. 3. radius on all corners is 0.152 max., unless otherwise specified. 4. package wrapage: 0.012 max. 5. no plastic flash allowed on the top and bottom lead surface. 6. pad planarity: 0.102 7. crack between plastic body and lead is not allowed. recommended land pattern dimensions in millimeters dimensions in inches unit: mm symbols min. typ. max. a a1a2 e e1e2 e3 d d1d2 d3 l l1l2 l3 l4 l5 be 0.800.00 3.90 2.95 1.65 2.95 3.90 0.65 0.75 1.10 0.35 0.57 0.23 0.57 0.30 0.17 0.20 0.90 ? 0.2 ref 4.003.05 1.75 3.05 4.00 0.75 0.85 1.20 0.40 0.62 0.28 0.62 0.35 0.27 0.25 0.50 bsc 1.000.05 4.10 3.15 1.85 3.15 4.10 0.85 0.95 1.30 0.45 0.67 0.33 0.67 0.40 0.37 0.30 symbols min. typ. max. a a1a2 e e1e2 e3 d d1d2 d3 l l1l2 l3 l4 l5 be 0.0310.000 0.153 0.116 0.065 0.116 0.1530.026 0.029 0.043 0.014 0.022 0.009 0.022 0.012 0.007 0.008 0.035 ? 0.008 ref 0.1570.120 0.069 0.120 0.157 0.030 0.033 0.047 0.016 0.024 0.011 0.0240.014 0.011 0.010 0.020 bsc 0.0390.002 0.161 0.124 0.073 0.124 0.161 0.034 0.037 0.051 0.018 0.026 0.013 0.026 0.016 0.015 0.012 d2 d3 l5 l1 l e3 b l3 d1 d1 l4 l2 e2 e1 e l5 d pin #1 dotby marking e a1 a a2 0.60 0.50 0.45 0.25 0.25 0.22 3.10 2.75 3.10 3.43 0.27 0.75 0.85 0.25 0.75 1.20 1.00 0.04 downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 14 of 15 tape and reel dimensions , qfn 4x4, 22 lead ep2_s carrier tapereel tape size 12mm reel size ?330 m ?330.0 2.0 n ?79.0 1.0 unit: mm g m w1 s k h n w v r trailer tape 300mm min. components tape orientation in pocket leader tape 500mm min. h ?13.0 0.5 w 12.4 +2.0/-0.0 w1 17.0 +2.6/-1.2 k 10.5 0.2 s 2.0 0.5 g ? r ? v ? leader/trailer and orientation unit: mm p1 d1 p2 b0 p0 d0 e2 e1 e a0 feeding direction package a0 b0 k0 ee 1 e 2 d0 d1 p0 p1 p2 t 4.35 0.10 0.10 4.35 0.10 1.10 1.50 1.50 12.00 0.10 1.75 0.05 5.50 0.10 8.00 0.10 4.00 0.05 2.00 0.05 0.30 0.30 +0.10/-0 min. qfn 4x4 (12mm) t k0 downloaded from: http:///
AOZ2253EQI-30 rev 1.1 march 2018 www.aosmd.com page 15 of 15 as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provi ded in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. legal disclaimer alpha and omega semiconductor makes no representation s or warranties with re spect to the accuracy or completeness of the information provid ed herein and takes no liabilities fo r the consequences of use of such information or any product described herein. alpha and om ega semiconductor reserves the right to make changes to such information at any time without further notice. this document does not constitute the grant of any intellectual property rights or representation of non-infringement of any third partys intellectual property rights. life support policy alpha and omega semiconductor products are not author ized for use as critical components in life support devices or systems. part marking part number part number code of marking AOZ2253EQI-30 acem aoz2253eqi-31 acew acem option code assembly lot code year & week code ywlt AOZ2253EQI-30 (qfn4x4) part number code downloaded from: http:///


▲Up To Search▲   

 
Price & Availability of AOZ2253EQI-30

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X